Dalian anchorage plastic manufacturers to supply various types of anchorage glue epoxy structural adhesive, plastic injection anchorage, anchorage plastic syringe welcome to purchase! JGJ-17 construction adhesive anchorage Published: 2013-8-8 seaside Dalian Greentech Building Materials Co., grout, adhesives, self-leveling, sealant, waterproofing materials, concrete additives, polymer mortar, railway mortar JGJ-17 construction adhesive anchorage I. Product Overview solvent-free, two-component modified epoxy resin. Second, the technical indicators of the mixing ratio of the weight of Bijia: B = 4: 1 package has been scaled provisioning, A: 16kg; B: 4kg color A + B for concrete gray Density (g / cm3, 25 ℃) 1.50 ± 0.05 at the beginning viscosity 80 to 90 minutes mechanical properties (mPa · s, 25 ℃ degrees) soft paste pot life (1kg, 25 ℃) :( mixed on the 7th, 25 ℃) splitting tensile strength of 53.0 MPa compressive bending 9.06MPa strength of 74.7 MPa steel - steel (steel sleeve method) tensile shear strength standard value 18.9 MPa restraint strap bond strength under conditions rib pullout steel and concrete C30, Φ25, L = 150mm 14.66 MPa C60, Φ25, L = 125mm 19.04 MPa nonvolatile content of 99.3% Third, the use of Dalian anchorage plastic manufacturers to supply various types of anchorage glue epoxy structural adhesive, plastic injection anchorage, anchorage plastic syringe welcome to purchase! 1. Application: steel / bolts anchoring agent. 2, pretreatment: Before anchoring in concrete structures drilling, remove dust hole, water, steel surface rust, decontamination, roughening. 3. Mix: bulk plastic: not to exceed 300 rpm low speed agitation were A and Part B, then press the A: B = 4: 1 weight ratio of accurate weighing A, B component. With B down in the container, with no more than 300 revolutions of the low-speed stirring until the color is completely homogeneous. In the process of stirring, the stirrer to ensure that all parts of the contact, so as to obtain optimum mixing results. 4. Note: 1) mixing the gel must be uniform, otherwise it will affect the bond strength. 2) once the gel volume should not be too much, now with the current, a good tune glue must be used during the applicable period. At higher ambient temperatures the gel too, will shorten the glue pot. With plastic containers should be large enough to put a rapid cooling after heat glue reactions. 3) Adhesive tool can not be mixed, A and B were mixed drums lid can not cover the remaining material must be sealed after you take plastic. 5, plastic injection: The resin mixed into the hole, plastic injection amount should be more than two-thirds of the volume of drilling. 6, anchorage / Screw: will handle good steel or screw inserted into the hole, slowly rotates to release the bar, make the hole and reinforced overall bonding. Do not move the resin is cured before the anchor, to avoid affecting the anchoring effect. 7. Advantages: Construction in the wet base surface curing; non-expansive chemical adhesion, without causing damage to the substrate. Fourth, packaging and storage: 1, the product is metal pail, Packing A: 4k g + B: 1k g / groups. Engineering equipment can press A: 16k g + B: 4k g / groups. 2, sealed and stored in a cool, dry, well-ventilated place, storage temperature 0 ℃ ~ 4 0 ℃. Shelf life of 12 months. Note: This product is safe, non-toxic, non-flammable, can meet the transport requirements of the transport sector. Skin, clothes uncured glue with a rag dipped in alcohol wipe has a clean, soapy water then. If accidentally splashed into the eyes, wash with plenty of water, and the nearest doctor. If accidentally swallowed, Do not induce vomiting and seek immediate medical attention to the blues. Dalian anchorage plastic manufacturers to supply various types of anchorage glue epoxy structural adhesive, plastic injection anchorage, anchorage plastic syringe welcome to purchase Dalian anchorage plastic manufacturers to supply various types of anchorage glue epoxy structural adhesive, injection anchorage plastic, anchorage glue syringe welcome to purchase!